| 螺距p | 粗牙螺纹大径d | 螺纹收尾l(不大于) | 肩距a(不大于) | 退刀槽 | 倒角C | ||||||
| 一般 | 短的 | 一般 | 长的 | 短的 | b\一般 | b\窄的 | r | d3 | |||
| 0.2 | - | 0.5 | 0.25 | 0.6 | 0.8 | 0.4 | - | - | 0.5p | - | 0.2 |
| 0.25 | 1;1.2 | 0.6 | 0.3 | 0.75 | 1 | 0.5 | 0.75 | - | 0.5p | - | 0.2 |
| 0.3 | 1.4 | 0.75 | 0.4 | 0.9 | 1.2 | 0.6 | 0.9 | - | 0.5p | - | 0.3 |
| 0.35 | 1.6;1.8 | 0.9 | 0.45 | 1.05 | 1.4 | 0.7 | 1.05 | - | 0.5p | d-0.6 | 0.3 |
| 0.4 | 2 | 1 | 0.5 | 1.2 | 1.6 | 0.8 | 1.2 | - | 0.5p | d-0.7 | 0.4 |
| 0.45 | 2.2;2.5 | 1.1 | 0.6 | 1.35 | 1.8 | 0.9 | 1.35 | - | 0.5p | d-0.7 | 0.4 |
| 0.5 | 3 | 1.25 | 0.7 | 1.5 | 2 | 1 | 1.5 | 1 | 0.5p | d-0.2 | 0.5 |
| 0.6 | 3.5 | 1.5 | 0.75 | 1.8 | 2.4 | 1.2 | 1.8 | 1 | 0.5p | d-1.0 | 0.5 |
| 0.7 | 4 | 1.75 | 0.9 | 2.1 | 2.8 | 1.4 | 2.1 | 1 | 0.5p | d-1.1 | 0.6 |
| 0.75 | 4.5 | 1.9 | 1 | 2.25 | 3 | 1.5 | 2.25 | 1.5 | 0.5p | d-1.2 | 0.6 |
| 0.8 | 5 | 2 | 1 | 2.4 | 3.2 | 1.6 | 2.4 | 1.5 | 0.5p | d-1.3 | 0.8 |
| 1 | 6;7 | 2.5 | 1.25 | 3 | 4 | 2 | 3 | 1.5 | 0.5p | d-1.6 | 1 |
| 1.25 | 8 | 3.2 | 1.6 | 4 | 5 | 2.5 | 3.75 | 1.5 | 0.5p | d-2.0 | 1.2 |
| 1.5 | 10 | 3.8 | 1.9 | 4.5 | 6 | 3 | 4.5 | 2.5 | 0.5p | d-2.3 | 1.5 |
| 1.75 | 12 | 4.3 | 2.2 | 5.3 | 7 | 3.5 | 5.25 | 2.5 | 0.5p | d-2.6 | 2 |
| 2 | 14;16 | 5 | 2.5 | 6 | 8 | 4 | 6 | 3.5 | 0.5p | d-3.0 | 2 |
| 2.5 | 18;20;22 | 6.3 | 3.2 | 7.5 | 10 | 5 | 7.5 | 3.5 | 0.5p | d-3.6 | 2.5 |
| 3 | 24;27 | 7.5 | 3.8 | 9 | 12 | 6 | 9 | 4.5 | 0.5p | d-4.4 | 2.5 |
| 3.5 | 30;33 | 9 | 4.5 | 10.5 | 14 | 7 | 10.5 | 4.5 | 0.5p | d-5.0 | 3 |
| 4 | 36;39 | 10 | 5 | 12 | 16 | 8 | 12 | 5.5 | 0.5p | d-5.7 | 3 |
| 4.5 | 42;45 | 11 | 5.5 | 13.5 | 18 | 9 | 13.5 | 6 | 0.5p | d-6.4 | 4 |
| 5 | 48;52 | 12.5 | 6.3 | 15.5 | 20 | 10 | 15 | 6.5 | 0.5p | d-7.0 | 4 |
| 5.5 | 56;60 | 14 | 7 | 16.5 | 22 | 11 | 17.5 | 7.5 | 0.5p | d-7.7 | 5 |
| 6 | 64;68 | 15 | 7.5 | 18 | 24 | 12 | 18 | 8 | 0.5p | d-8.3 | 5 |
