目录 ANSI ASME API ASTM IEEE ISA DIN BS ISO NF JIS EN
NF——法国标准化协会目录
编号 中文名称 英文名称
NF E22-513-1987 滑动轴承.整体铜合金套筒.尺寸与公差 (Plain bearings. Solid copper alloy bushes. Dimensions and tolerances.)
NF E22-515-1983 滑动轴承.薄型半边轴瓦.尺寸,公差和检验方法 (PLAIN BEARINGS. THIN-WALLED HALF BEARINGS. DIMENSIONS, TOLERANCES AND METHODS OF CHECKING.)
NF E22-516-1984 滑动轴承.薄型凸缘半边轴瓦.尺寸,公差和控制方法 (PLAIN BEARINGS. THIN-WALLED FLANGED HALF BEARINGS. DIMEBSIONS,TOLERANCES AND METHODS OF CHECKING.)
NF E22-517-1984 滑动轴承.薄型半边轴瓦.伸长度的检验方法 (PLAIN BEARINGS. THIN-WALLED HALF BEARINGS. METHOD OF PERIPHERAL LENGTH CHECKING.)
NF E22-520-1984 滑动轴承.带状材料制的止推垫圈.尺寸和公差 (PLAIN BEARINGS. RING TYPES THRUST WASHERS MADE FROM STRIP. DIMENSIONS AND TOLERANCES.)
NF E22-521-1984 滑动轴承.在压机上切边的双金属半止推垫圈.特性和公差 (PLAIN BEARINGS. PRESSED BIMETALLIC HALF THRUST WASHERS. FEATURES AND TOLERANCES.)
NF E22-550-1992 滑动轴承.厚壁滑动轴承用多层材料 (Plain bearings. Multilayer materials for thin-walled plain bearings.)
NF E22-551-1992 滑动轴承.多层滑动轴承用的铅和锡铸造合金 (Plain bearings. Lead and tin casting alloys for multilayer plain bearings.)
NF E22-552-1986 滑动轴承.厚壁多层轴承合金底衬的要求 (PLAINS BEARINGS. REQUIREMENTS ON BACKINGS FOR THICK-WALLED MULTILAYER BEARINGS.)
NF E22-553-1992 滑动轴承.铜合金.第1部分:整块的和多层厚壁滑动轴承用铸铜合金 (Plain bearings. Copper alloys. Part 1 : cast copper alloys for solid and multilayer thick-walled plaint bearings.)
NF E22-554-1992 滑动轴承.铜合金.第2部分:整块铜合金滑动轴承用锻铜合金 (Plain bearing. Copper alloys. Part 2 : wrough copper alloys for solid plain bearings.)
NF E22-555-1985 滑动轴承.整体轴承用的铝合金 (Plain bearings. Aluminium alloy for solid bearings.)
NF E22-561-1986 滑动轴承.轴承材料硬度试验.第1部分:复合材料 (PLAIN BEARINGS. HARDNESS TESTING OF BEARING METALS. PART 1 : COMPOUND METERIALS.)
NF E22-563-1988 滑动轴承.金属薄壁轴瓦.0.01弹性极限值的测定 (Plain bearings. Metallic thin-walled half bearings. Determination of the sigma 0,01 elastic limit.)
NF E22-564-1993 滑动轴承.多层金属滑动轴承.第3部分:无损穿透性试验 (PLAIN BEARINGS. METALLIC MULTILAYER PLAIN BEARINGS. PART 3 : NON-DESTRUCTIVE PENETRANT TESTING.)
NF E22-570-1987 滑动轴承.金属轴承材料的压缩试验 (PLAIN BEARINGS. COMPRESSION TESTING OF METALLIC BEARING MATERIALS.)
NF E22-571-1986 滑动轴承.轴承材料硬度试验.第2部分:整体材料 (PLAIN BEARINGS. HARDNESS TESTING OF BEARING METALS. PART 2 : SOLID MATERIALS.)
NF E22-580-1987 滑动轴承.耐磨材料摩擦性能试验.第1部份:带耐磨材料,配料和油的组件在极限润滑条件下摩擦与磨损性能试验 (PLAIN BEARINGS. TESTING OF THE TRIBOLOGICAL BEHAVIOUR OF BEARING MATERIALS. PART 1 : TESTING OF THE FRICTION AND WEAR BEHAVIOUR OF BEARING MATERIAL/MATING MATERIAL/OIL COMBINATIONS UNDER CONDITIONS OF BOUNDARY LUBRICATION.)
NF E22-601-1985 联轴节.工业万向接头传动.定义.特性 (Couplings. Industrial cardan shaft. Definition. Characteristics.)
NF E22-603-1985 联轴节.工业万向接头传动.验收 (Couplings. Industrial cardan shaft. Acceptance.)
NF E22-604-1985 联轴节.工业万向接头传动.用法兰盘固定 (Couplings. Industrial cardan shaft. Flange mounting.)
NF E22-610-1986 机械传动.联轴节部件.分类.术语.图形符号 (Mechanical transmissions. Coupling devices. Classification. Terminology. Graphical symbols.)
NF E22-611-1983 机械传动.联节轴部件.作用.名称.应用范围 (Mechanical transmissions. Couplings. Function, designation and field of use.)
NF E22-612-1979 机械传动.联节轴部件.带发动机的机器的安装和校准的一般条件 (MECHANICAL TRANSMISSIONS. COUPLINGS. GENERAL CONDITIONS OF INSTALLATION AND ALIGNMENT OF A MACHINE WITH ITS MOTOR.)
NF E22-613-1983 机械传动.联轴节.挠性和弹性联轴节的计算 (Mechanical transmissions. Couplings. Calculation of flexible or elastic couplings.)
NF E22-614-1986 械械传动.联节轴部件.选配联轴节所需的工业部件 (Mechanical transmissions. Coupling devices. Technical elements necessary for the selection of a coupler.)
NF E22-620-1980 固定环连接.尺寸.公差和通常连接的表面状态 (PRESSED-ON ASSEMBLIES. DIMENSIONS,TOLERANCES AND SURFACE CONDITION OF USUAL ASSEMBLIES.)
NF E22-621-1984 固定环连接.在圆柱支承面上.功能,操作,计算 (Pressed-on assemblies on cylindrical bearings. Function. Realisation. Calculation.)
NF E23-001-1-1998 齿轮术语词汇.第1部分:有关几何学上的定义 (Vocabulary of gear terms. Part 1 : definitions related to geometry.)
NF E23-002-1988 齿轮词汇.几何定义.螺旋齿轮 (GEARS. GLOSSARY OF WORM GEAR PAIRS. GEOMETRICAL DEFINITIONS.)
NF E23-005-1998 齿轮的国际符号表示法.几何参数符号 (International gear notation. Symbols for geometrical data.)
NF E23-007-1-1995 圆柱齿轮.准确度的ISO体系.第1部分:齿轮齿对应齿根面相应偏差的容许值和定义 (Cylindrical gears. ISO system of accuracy. Part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth.)
NF E23-007-2-1997 圆柱齿轮.ISO 体系的准确度.第2部分:有关放射要素偏差度和输出信息的相应偏差的容许值和定义 (CYLINDRICAL GEARS. ISO SYSTEM OF ACCURACY. PART 2 : DEFINITIONS AND ALLOWABLE VALUES OF DEVIATIONS RELEVANT TO RADIAL COMPOSITE DEVIATIONS AND RUNOUT INFORMATION.)
NF E23-009-1998 普通和重型技术设备用圆柱齿轮.标准基本齿条齿牙剖面 (Cylindrical gears for general and heavy engineering. Standard basic rack tooth profile.)
NF E23-014-1994 齿轮.ISO术语.齿轮齿术语:磨损和损坏 (Gears. ISO system of terminology. Terminology for the appearance of gear teeth : wear and damages.)
NF E23-016-1986 锥形直的齿轮.给齿轮工人的说明书 (STRAIGHT BEVEL GEARS. INFORMATION TO BE GIVEN TO THE MANUFACTURER.)
NF E23-018-1988 蜗轮供货要求 (WORM GEARS. INFORMATION TO BE GIVEN TO THE MANUFACTURER.)
NF E23-022-1-2002 齿轮装置的验收标准.第1部分:空气声的测试标准 (Acceptance code for gear units - Part 1 : test code for airborne sound.)
NF E23-030-1-2002 正齿轮和斜齿轮承载能力的计算.第1部分:基本原理、说明和一般影响因素 (Calculation of load capacity of spur and helical gears - Part 1 : basic principles, introduction and general influence factors.)
NF E23-030-2-2003 正齿轮和斜齿轮承载能力的计算.第2部分:齿轮表面耐用能力的计算 (Calculation of load capacity of spur and helical gears - Part 2 : calculation of surface durability (pitting).)
NF E23-030-3-2003 正齿轮和斜齿轮承载能力的计算.第3部分:轮齿弯曲强度的计算 (Calculation of load capacity of spur and helical gears - Part 3 : calculation of tooth bending strength.)
NF E23-030-5-2003 直齿轮和斜齿轮承载能力的计算.第5部分:材料的强度和质量 (Calculation of load capacity of spur and helical gears - Part 5 : strength and quality of materials.)
NF E23-035-2003 石油和天然气工业.特殊用途高速齿轮部件 (Petroleum and natural gas industries - High speed special-purpose gear units.)
NF E23-150-1977 链条传动.链条长度和轴距的计算 (CHAIN TRANSMISSIONS.CALCULATION OF CHAIN LENGTHS AND DISTANCES BETWEEN CENTRES.)
NF E24-001-1996 皮带传动.V带、V肋带及对应槽轮.词汇 (Belt drives. V-belts and V-ribbed belts, and corresponding grooved pulleys. Vocabulary.)
NF E24-205-1990 皮带传动.梯形皮带用槽轮(在有效宽度范围的基本型式).皮带轮凹槽的几何检验 (BELT DRIVES. GROOVED PULLEYS FOR V-BELTS (SYSTEM BASED ON EFFECTIVE WIDTH). GEOMETRICAL INSPECTION OF GROOVES.)
NF E24-221-1995 皮带传动.窄接合型三角皮带.有效长度 (Belt drives. Narrow joined V-belts. Lengths in effective system.)
NF E24-301-1-1989 同步皮带传动.皮带.第1部分:节距符号MXL、XL、L、H、XH和XXH;米制和英制尺寸 (Synchronous belt drives. Belts. Part 1 : pitch codes mxl, XL,L,H, XH and XXH. Metric and inch dimensions.)
NF E24-301-2-1989 同步皮带传动.皮带.第2部分:节距符号 MXL和XXL.米制尺寸 (Synchronous belt drives. Belts. Part 2 : pitch codes mxl and XXL. Metric dimensions.)
NF E24-312-1991 皮带传动.抗静电、无中断同步皮带的电导率.规范和试验方法 (BELT DRIVES. ELECTRICAL CONDUCTIVITY OF ANTISTATIC ENDLESS SYNCHRONOUS BELTS. CHARACTERISTICS AND TEST METHOD.)
NF E24-403-1995 皮带传动.V-线皮带.直线密度的定义 (BELT DRIVES. V-RIBBED BELTS. DETERMINATION OF LINEAR DENSITY.)
NF E24-404-1995 皮带传动.V型加筋皮带.间距,角度和拉线位置的测定 (BELT DRIVES. V-RIBBED BELTS. DETERMINATION OF MEASUREMENT OF PITCH, ANGLE AND CORD POSITION.)
NF E24-405-1997 皮带传动.V型加筋皮带.工业用PJ和PH型材的动力试验方法(家用) (BELT DRIVES. V-RIBBED BELTS. DYNAMIC TEST METHODS FOR PJ AND PH PROFILES FOR INDUSTRIAL APPLICATIONS (SPECIFIC TO DOMESTIC APPLIANCES).)
NF E25-001-2003 紧固件.质量保证体系 (Fasteners - Quality assurance system.)
NF E25-004-1984 紧固件.简单标记 (Fasteners. Short notations.)
NF E25-006-2000 紧固件.验收检验 (Fasteners - Acceptance inspection.)
NF E25-007-1982 紧固件.定货和供货条件 (Fasteners. Order and delivery specifications.)
NF E25-009-1999 紧固件.电镀层 (Fasteners - Electroplated coatings.)
NF E25-011-1992 紧固件的机械特性.由非亚铁金属制造的螺栓,螺钉,柱螺栓和螺母 (MECHANICAL PROPERTIES OF FASTENERS. BOLTS, SCREWS, STUDS AND NUTS MADE OF NON-FERROUS METALS. (EUROPEAN STANDARD EN 28839).)
NF E25-019-2000 紧固件.ISO米制外螺纹部件的端头 (Fasteners - Ends of parts with external ISO metric screw thread.)
NF E25-021-1994 螺钉的十字槽(欧洲标准EN ISO 4757) (Cross recesses for screws.)
NF E25-022-1-2001 紧固件公差.螺栓、螺钉、双头螺栓和螺母.第1部分:产品等级A、B及C (Tolerances for fasteners - Bolts, screws, studs and nuts - Part 1 : product grades A, B and C.)
NF E25-022-1987 紧固件.F级螺钉和螺帽公差(精密机械).螺纹直径1到3mm (FASTENERS. TOLERANCES FOR BOLTS,SCREWS AND NUTS PRODUCT GRADE F (FINE MECHANIC). THREAD DIAMETERS FROM 1 UP TO 3 MM.)
NF E25-023-1992 紧固件.螺栓和螺钉的自由尺寸孔 (Fasteners. Clearance hole for bolts and screws.)
NF E25-035-1995 紧固件.不锈钢螺纹连接件.试验方法.使用合格证 (FASTENERS. STAINLESS STEEL THREADED CONNECTIONS. TEST METHODS. FITNESS FOR USE.)
NF E25-040-2000 紧固件.非电解用锌片覆层 (Fasteners - Non-electrolytically applied zinc flake coatings.)
NF E25-042-2003 耐腐蚀不锈钢紧固件的钝化 (Passivation of corrosion-resistant stainless-steel fasteners.)
NF E25-100-1-1999 碳钢合金制成的紧固件的机械性能.第1部分:螺栓、螺钉和螺柱 (Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1 : bolts, screws and studs.)
NF E25-100-3-1992 紧固件.表面不连续性.第1部分:一般要求的螺栓、螺钉和螺柱 (FASTENERS. SURFACE DISCONTINUITIES. PART 1 : BOLTS, SCREWS AND STUDS FOR GENERAL REQUIREMENTS. (EUROPEAN STANDARD EN 26157-1).)
NF E25-100-4-1992 紧固件.表面不连续性.第3部分:特殊要求的螺栓、螺钉和螺柱 (FASTENERS. SURFACE DISCONTINUTIES. PART 3 : BOLTS, SCREW AND STUDS FOR SPECIAL REQUIREMENTS. (EUROPEAN STANDARD EN 26157-3).)
NF E25-100-5-1998 碳钢和不锈钢制紧固件的机械性能.第5部分:不处在拉伸应力下的固定螺钉和类似螺纹紧固件 (Mechanical properties of fasteners made of carbon steel and alloy steel. Part 5 : set screws and similar threaded fasteners not under tensile stresses.)
NF E25-100-6-1998 不锈钢紧固件耐腐蚀的机械特性.螺栓,螺丝和双端螺栓 (Mechanical properties of corrosion-resistant stainless-steel fasteners. Part 1 : bolts, screws and studs.)
NF E25-100-7-1995 紧固件的机械性能.第7部分:公称直径1-10mm的螺栓和螺钉的扭力试验和最小扭矩 (MECHANICAL PROPERTIES OF FASTENERS. PART 7 : TORSIONAL TEST AND MINIMUM TORQUES FOR BOLTS AND SCREWS WITH NOMINAL DIAMETERS 1 MM TO 10 MM. (EUROPEAN STANDARD EN 20898-7).)
NF E25-100-8-1998 不锈钢紧固件耐腐蚀的机械特性.不低于拉伸应力下配套螺钉和类似紧固件 (Mechanical properties of corrosion-resistant stainless-steel fasteners. Part 3 : set screws and similar fasteners not under tensile stress.)
NF E25-101-1996 技术产品文献加工.弹簧.第2部分:圆柱螺旋状压缩弹簧的数据表示(欧洲标准EN ISO 2162-2) (Technical product documentation. Springs. Part 2 : presentation of data for cylindrical helical compression springs.)
NF E25-102-1977 拉力弹簧.给制造者的指示 (TENSION SPRINGS. INFORMATION TO BE SUPPLIED TO THE MANUFACTURER.)
NF E25-103-1977 扭力弹簧.给制造者的指示 (TORSIONAL SPRINGS. INFORMATION TO BE SUPPLIED TO THE MANUFACTURER.)
NF E25-104-1978 锥形弹簧垫圈.动力垫圈,所谓盘形弹簧 (CONICAL SPRING WASHERS. DYNAMIC WASHERS (OR SO-CALLED BELLEVILLE SPING WASHERS).)
NF E25-105-1996 技术产品文献.弹簧.第3部分:词汇 (Technical product documentation. Springs. Part 3 : vocabulary.)
NF E25-106-2-2002 圆线和圆棒制成的圆柱螺旋弹簧.计算和设计.第2部分:拉簧 (Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2 : extension springs.)
NF E25-106-3-2002 圆线和圆棒制成的圆柱螺旋弹簧.计算和设计.第3部分:扭杆弹簧 (Cylindrical helical springs made from round wire and bar - Calculation and design - Part 3 : torsion springs.)
NF E25-107-1983 金属用螺钉.内部六叶埋头.A级.符号FX (SCREWS. SIX LOBES RECESSED CONTERSUNK HEAD. PRODUCT GRADE A. SYMBOL FX.)
NF E25-108-2001 半埋头内六角螺钉 (Hexalobular socket raised countersunk head screws.)
NF E25-109-2001 平头内六角螺钉 (Hexalobular socket pan head screws.)
NF E25-110-2001 圆柱头内六角螺钉 (Hexalobular socket head cap screws.)
NF E25-111-2001 凸头内六角螺钉 (Hexalobular socket cheese head screws.)
NF E25-112-2001 六角头螺栓.产品等级A和B (Hexagon head bolts - Product grades A and B.)
NF E25-113-1992 紧固件.六角头螺栓.B级、缩杆制品 (Fasteners. Hexagon head bolts. Product grade B. Reduced shank (shank diameter = pitch diameter).)
NF E25-114-2001 六角头螺钉.产品等级A和B (Hexagon head bolts - Product grades A and B.)
NF E25-115-1-2001 六角头螺栓.产品等级C (Hexagon head bolts - Product grade C.)
NF E25-115-2-2001 六角头螺钉.产品等级C (Hexagon head screws - Product grade C.)
NF E25-116-1983 金属用螺钉.方头.标准杆.A和B级.符号Q (Square head screws. Product grades A and B. Symbol Q.)
NF E25-117-1983 金属用螺钉.方头.全螺纹.A和B级.符号Q (Square head screws. Product grades A and B. Symbol Q.)
NF E25-118-1983 金属用螺钉.方头.C级.符号Q (Square head screws. Product grade C. Symbol Q.)
NF E25-119-1-1994 带有H型或Z型的十字槽沉头螺钉(普通头型).产品等级A.第1部分:性能类别4.8的钢 (Countersunk flat head screws (common head style) with type H or type Z cross recessed. Product grade A. Part 1 : steel of property class 4.8.)
NF E25-119-2-1994 十字槽沉头螺钉(一般头形).等级A.第2部分:8.8类特性钢,不锈钢和有色金属 (Cross recessed countersunk flat head scews (common head style). Grade A. Part 2 : steel of property class 8.8, stainless steel and non-ferrous metals.)
NF E25-120-1994 带有H型或Z型的十字槽半沉头螺钉(普通头型).产品等级A (Countersunk raised head screws (common head style) with type H or type Z cross recessed. Product grade A.)
NF E25-121-1994 带有H型或Z型十字槽的平圆头螺钉.产品等级A (Pan head screws with type H or type Z cross recess. Product grade A.)
NF E25-122-1984 金属用螺钉.称作“POLIER“的Z十字槽宽圆头.A级.符号RLZ (SCREWS. CROSS RECESSED MUSHROOM HEAD (POELIERS). PRODUCT GRADE A. SYMBOL RL Z.)
NF E25-123-1994 一字槽沉头螺钉(普通头型).产品等级A (Slotted countersunk flat head screws (common head style). Product grade A.)
NF E25-124-1994 一字槽半沉头螺钉(普通头型).产品等级A (Slotted raised countersunk head screws (common head style). Product grade A.)
NF E25-126-1997 内六角圆头螺钉 (HEXAGON SOCKET BUTTON HEAD SCREWS. (EUROPEAN STANDARD EN ISO 7380).)
NF E25-128-1994 一字槽平圆头螺钉.产品等级A (Slotted pan head screws. Product grade A.)
NF E25-130-1986 加垫圈的金属用螺钉.锥形光滑压紧垫圈.A级 (SCREWS WITH CONICAL SPRING TIGHTENING WASHER. PRODUCT GRADE A.)
NF E25-131-1986 加垫圈的金属用螺钉.内齿锥形垫圈.A级 (SCREWS WITH CONICAL SPRING INTERNAL TOOTHED TIGHTENING WASHER. PRODUCT GRADE A.)
NF E25-132-1986 加垫圈的金属用螺钉.外齿垫圈.A级 (SCREWS WITH SERRATED EXTERNAL OVERLAPED TOOTHED LOCK TIGHTENNING WASHER. PRODUCT GRADE A.)
NF E25-133-1987 紧固件.螺杆千斤顶用的金属螺钉.短六角头长制动端螺钉.A和B级.符号HZ (Fasteners. Screws for screw-jacks. Small hexagon head screws with long dog point. Product grades A and B. Symbol HZ.)
NF E25-134-1987 紧固件.螺杆千斤顶用的金属螺钉.短方头短制动端螺钉.A和B级.符号QZ (Fasteners. Screws for screw-jacks. Small square head screws with short dog point. Product grades A and B. Symbol QZ.)
NF E25-136-1986 紧固件.螺杆.A和B级产品 (Fasteners. Threaded rods. Product grades A and B.)
NF E25-139-1987 紧固件.金属用螺钉.Z十字槽宽凸圆柱形头.A级.符号CBLZS (FASTENERS. SCREWS. Z CROSS RECESSED AND SLOTTED PAN HEAD. GRADE A. SYMBOL CBL ZS.)
NF E25-140-1994 紧固件.电弧焊接双端螺栓.符号SA.尺寸和物理化学特性.拉制电弧焊接螺栓系统 (FASTENERS. ARC WELDING STUDS LOADING. SYMBOL SA. DIMENSIONS AND PROPERTIES PHYSICAL-CHIMICAL. DRAWN ARC STUD WELDING SYSTEM.)
NF E25-142-1991 紧固件.电阻焊金属螺钉.缩小头 (FASTENERS. RESISTANCE WELDING SCREWS. REDUCED HEAD. SYMBOL Z. SR.)
NF E25-143-1991 紧固件.电容器电焊全螺纹螺柱 (FASTENERS. WELDINGSTUDS BY CONDENSOR DISCHARGE. SYMBOL SD.)
NF E25-144-1991 紧固件.电弧焊全螺纹螺柱 (FASTENERS. ENTIRELY THREADED ARC WELDING STUDS. SYMBOL SF.)
NF E25-145-1991 紧固件.电弧焊不完全螺纹螺柱 (FASTENERS. PARTIALLY THREADED ARC WELDING STUDS. SYMBOL SF.)
NF E25-149-1998 十字槽圆头螺钉 (CROSS RECESSED CHEESE HEAD SCREWS. (EUROPEAN STANDARD EN ISO 7048).)
NF E25-150-1998 带平垫圈的螺钉和垫圈组件.垫圈强度等级为200 HV和300 HV. (Screw and washer assemblies with plain washers. Washer hardness classes 200 HV and 300 HV.)
NF E25-151-2001 米制细牙螺纹的六角头螺钉.产品等级A和B (Hexagon head screws with metric fine pitch thread - Product grades A and B.)
NF E25-152-2001 米制细牙螺纹的六角头螺栓.产品等级A和B (Hexagon head bolts with metric fine pitch thread - Product grades A and B.)
NF E25-160-1992 平端开槽调整螺钉 (SLOTTED SET SCEWS WITH FLAT POINT. (EUROPEAN STANDARD EN 24766).)
[1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] [21] [22] [23] [24] [25] [26] [27] [28] [29] [30] [31] [32] [33] [34] [35] [36] [37] [38] [39] [40] [41] [42] [43] [44] [45] [46] [47] [48] [49] [50] [51] [52] [53] [54] [55] [56] [57] [58] [59] [60] [61] [62] [63] [64] [65] [66] [67] [68] [69] [70] [71] [72] [73] [74] [75] [76] [77] [78] [79] [80] [81] [82] [83] [84] [85] [86] [87] [88] [89] [90] [91] [92] [93] [94] [95] [96] [97] [98] [99] [100] [101] [102] [103] [104] [105] [106] [107] [108] [109] [110] [111] [112] [113] [114] [115] [116] [117] [118] [119] [120] [121] [122] [123] [124] [125] [126] [127] [128] [129] [130] [131] [132] [133] [134] [135] [136] [137] [138] [139] [140] [141] [142] [143] [144] [145] [146] [147] [148] [149] [150] [151] [152] [153] [154] [155] [156] [157] [158] [159] [160] [161] [162] [163] [164] [165] [166] [167] [168] [169] [170] [171] [172] [173] [174] [175] [176] [177] [178] [179] [180] [181] [182] [183] [184] [185] [186] [187] [188] [189] [190] [191] [192] [193] [194] [195] [196] [197]